109 lines
3.6 KiB
Plaintext
109 lines
3.6 KiB
Plaintext
|
# This is an example resource file for rTorrent. Copy to
|
||
|
# ~/.rtorrent.rc and enable/modify the options as needed. Remember to
|
||
|
# uncomment the options you wish to enable.
|
||
|
|
||
|
# Maximum and minimum number of peers to connect to per torrent.
|
||
|
#min_peers = 40
|
||
|
#max_peers = 100
|
||
|
|
||
|
# Same as above but for seeding completed torrents (-1 = same as downloading)
|
||
|
#min_peers_seed = 10
|
||
|
#max_peers_seed = 50
|
||
|
|
||
|
# Maximum number of simultanious uploads per torrent.
|
||
|
#max_uploads = 15
|
||
|
|
||
|
# Global upload and download rate in KiB. "0" for unlimited.
|
||
|
#download_rate = 0
|
||
|
#upload_rate = 0
|
||
|
|
||
|
# Default directory to save the downloaded torrents.
|
||
|
directory = /home/burchettm/BitTorrent
|
||
|
|
||
|
# Default session directory. Make sure you don't run multiple instance
|
||
|
# of rtorrent using the same session directory. Perhaps using a
|
||
|
# relative path?
|
||
|
session = ./.rtorrent/session
|
||
|
|
||
|
# Watch a directory for new torrents, and stop those that have been
|
||
|
# deleted.
|
||
|
#schedule = watch_directory,5,5,load_start=./watch/*.torrent
|
||
|
#schedule = untied_directory,5,5,stop_untied=
|
||
|
|
||
|
# Close torrents when diskspace is low.
|
||
|
#schedule = low_diskspace,5,60,close_low_diskspace=100M
|
||
|
|
||
|
# Stop torrents when reaching upload ratio in percent,
|
||
|
# when also reaching total upload in bytes, or when
|
||
|
# reaching final upload ratio in percent.
|
||
|
# example: stop at ratio 2.0 with at least 200 MB uploaded, or else ratio 20.0
|
||
|
#schedule = ratio,60,60,"stop_on_ratio=200,200M,2000"
|
||
|
|
||
|
# The ip address reported to the tracker.
|
||
|
#ip = 127.0.0.1
|
||
|
#ip = rakshasa.no
|
||
|
|
||
|
# The ip address the listening socket and outgoing connections is
|
||
|
# bound to.
|
||
|
#bind = 127.0.0.1
|
||
|
#bind = rakshasa.no
|
||
|
|
||
|
# Port range to use for listening.
|
||
|
port_range = 42050-42050
|
||
|
|
||
|
# Start opening ports at a random position within the port range.
|
||
|
#port_random = no
|
||
|
|
||
|
# Check hash for finished torrents. Might be usefull until the bug is
|
||
|
# fixed that causes lack of diskspace not to be properly reported.
|
||
|
check_hash = no
|
||
|
|
||
|
# Set whetever the client should try to connect to UDP trackers.
|
||
|
#use_udp_trackers = yes
|
||
|
|
||
|
# Alternative calls to bind and ip that should handle dynamic ip's.
|
||
|
#schedule = ip_tick,0,1800,ip=rakshasa
|
||
|
#schedule = bind_tick,0,1800,bind=rakshasa
|
||
|
|
||
|
# Encryption options, set to none (default) or any combination of the following:
|
||
|
# allow_incoming, try_outgoing, require, require_RC4, enable_retry, prefer_plaintext
|
||
|
#
|
||
|
# The example value allows incoming encrypted connections, starts unencrypted
|
||
|
# outgoing connections but retries with encryption if they fail, preferring
|
||
|
# plaintext to RC4 encryption after the encrypted handshake
|
||
|
#
|
||
|
# encryption = allow_incoming,enable_retry,prefer_plaintext
|
||
|
|
||
|
# Enable DHT support for trackerless torrents or when all trackers are down.
|
||
|
# May be set to "disable" (completely disable DHT), "off" (do not start DHT),
|
||
|
# "auto" (start and stop DHT as needed), or "on" (start DHT immediately).
|
||
|
# The default is "off". For DHT to work, a session directory must be defined.
|
||
|
#
|
||
|
dht = auto
|
||
|
|
||
|
# UDP port to use for DHT.
|
||
|
#
|
||
|
dht_port = 42050
|
||
|
|
||
|
# Enable peer exchange (for torrents not marked private)
|
||
|
#
|
||
|
# peer_exchange = yes
|
||
|
|
||
|
#
|
||
|
# Do not modify the following parameters unless you know what you're doing.
|
||
|
#
|
||
|
|
||
|
# Hash read-ahead controls how many MB to request the kernel to read
|
||
|
# ahead. If the value is too low the disk may not be fully utilized,
|
||
|
# while if too high the kernel might not be able to keep the read
|
||
|
# pages in memory thus end up trashing.
|
||
|
#hash_read_ahead = 10
|
||
|
|
||
|
# Interval between attempts to check the hash, in milliseconds.
|
||
|
#hash_interval = 100
|
||
|
|
||
|
# Number of attempts to check the hash while using the mincore status,
|
||
|
# before forcing. Overworked systems might need lower values to get a
|
||
|
# decent hash checking rate.
|
||
|
#hash_max_tries = 10
|